125 W RMS par canal (8 ohms)
Impédance minimale 4 ohms (200 W RMS par canal)
Distorsion harmonique totale (DHT) 0.05 %
Réponse en fréquence 20 Hz - 20 kHz +/- 0,5 dB
Rapport signal/bruit > 110 dB (pondéré A)
Alimentation 100-240 V~50/60 Hz
Consommation 125 W
Formats d’entrée numérique PCM, Dolby Digital

custom amplifier solution, optimized for the highest level of performance and reliability

Type: 2.5-Way In-wall loudspeaker • Low Frequency Driver: Four 5.25” (130 mm) advanced Aluminum Matrix cone cast-frame woofers (JW13Al-4) • High Frequency Driver: 1” (25 mm) 2410H-2 Teonex® annular ring-diaphragm compression driver • Recommended Amplifier Power: 25 – 200W RM

Type: 2-way bookshelf loudspeaker • Low Frequency Driver: 6.5” (165mm) • Pure Pulp cone woofer • High Frequency Driver: 2410H-2 1-inch (25mm) annular ring, Teonex®diaphragm compression driver with advanced HDI™ geometry horn

12", 3-way Studio Monitor • Low-frequency transducer: 300 mm pure-pulp cone woofer (JW300SW-8) • Mid-frequency transducer: 125 mm pure pulp cone (JM125PC-8) • High-frequency transducer: 25 mm Magnesium-Aluminum alloy dome (054ALMg-1)

2-way 12" Studio Monitor Loudspeaker • Impedance: 8 Ohms • Maximum Recommended Amplifier Power: 200 Watts RMS

2-way Floorstanding Loudspeaker • Low-Frequency Transducer: 15" (380 mm) 2216Nd-1 Differential Drive® woofer • Mid/High Frequency Transducer: 3" (75 mm) D2430K dual compression

3-Way Floor Standing Loudspeaker ( RoseWood )
• Two 15" (38.1 cm) woofers
• 4" (10.2 cm) pure-beryllium diaphragm for crystal-clear highs
• 1" (2.5 cm), pure-beryllium diaphragm for extreme highs

In-wall Subwoofer • Dual 8” (200mm) low-profile, long-throw, Klippel-optimized, metal cone woofers

In-wall Passive Subwoofer • Two 10” (250mm) composite cone woofers • Designed for use with JBL Synthesis SDA amplifiers • Frequency Response 20Hz – 150Hz (-6dB) • Maximum Recommended Amplifier Power 600 Watts RMS

Dual 12” Passive Subwoofer • Maxiumum Recommended Amplifier Power: 1,200 watts RMS per channel

Dual 15-inch (380mm) in-room passive subwoofer • Recommended Amplifier Power: 2500 WRMS per woofer (5,000 WRMS total)

Pre-construction Bracket • For use as part of the installation process for the JBL Synthesis SCL-7 into new constructio

Pre-construction Bracket • For use as part of the installation process for the JBL Synthesis SCL-6 into new construction.

Type: 2-Way In-ceiling loudspeaker • Low Frequency Driver: 5.25” (130 mm) advanced Aluminum Matrix cone cast-frame woofer (JW130Al-4) • High Frequency Driver: 1” (25 mm) 2410H-2 Teonex® annular ring-diaphragm compression driver • Recommended Amplifier Power: 25 - 100 W RMS

Type: 2-Way In-wall loudspeaker • Low Frequency Driver: Two 5.25” (130 mm) advanced Aluminum Matrix cone cast-frame woofers (JW13Al-4) • High Frequency Driver: 1” (25 mm) 2410H-2 Teonex® annular ring-diaphragm compression driver • Recommended Amplifier Power: 25 – 150W RMS

Type: 2.5-Way In-wall loudspeaker • Low Frequency Driver: Four 5.25” (130 mm) advanced Aluminum Matrix cone cast-frame woofers (JW13Al-4) • High Frequency Driver: 1” (25 mm) 2410H-2 Teonex® annular ring-diaphragm compression driver • Recommended Amplifier Power: 25 – 200W RM

Type: 2-Way In-ceiling loudspeaker • Low Frequency Driver: 7” (180 mm) advanced Aluminum Matrix cone cast-frame woofer (JW180PB-6) • High Frequency Driver: 1” (25 mm) 2409H Teonex® annular ring-diaphragm compression driver • Recommended Amplifier Power: 25 – 125W RMS

Speaker Type: Two-way In-Wall Loudspeaker • Low Frequency Transducer: 7” (180mm) cast-frame, advanced aluminum matrix cone woofer • Mid/High Frequency Transducer: D2-derived 1” (25mm) 2409H annular ring, Teonex® diaphragm compression driver • Maximum Recommended Amplifier Power: 300 watts RMS

Speaker Type: Two-way In-Wall Loudspeaker • Low Frequency Transducer: Dual 5-¼” (130mm) cast-frame, advanced aluminum matrix cone woofers • Mid/High Frequency Transducer: D2-derived 1” (25mm) 2409H annular ring, Teonex® diaphragm compression driver • Maximum Recommended Amplifier Power: 300 watts RMS•